Needle roller bearing supplier factory today: N Series – Bearings of N design are single row cylindrical roller bearing and have two fixed ribs on the inner ring that retain the rollers and cage and one smooth outer ring. This design allows an axial displacement in certain limits, of the shaft in relation to the housing. Therefore, N Series rolling bearings are used in non-locating bearing units. Also, the N Series bearings have virtually no thrust capacity. NU Series – Are single row cylindrical roller bearings and have two fixed ribs on the outer ring and one smooth inner ring. This design allows an axial displacement in certain limits, of the shaft in relation to the housing. Therefore, NU Series rolling bearings are used in non-locating bearing units. Also, the NU Series bearings have no virtually thrust capacity. RNA 48 Series – Needle roller bearings that have metric dimensions, without Inner Rings, with/without Seals, precision ground raceways with ribs, cage guided rollers, and ISO 48 Dimensional Series. RNA 49 Series – Needle roller bearings that have metric dimensions, without Inner Rings, with/without Seals, precision ground raceways with ribs, cage guided rollers, and ISO 49 Dimensional Series. RNA 69 Series – Needle roller bearings that have metric dimensions, without Inner Rings, with/without Seals, precision ground raceways with ribs, cage guided rollers, and ISO 69 Dimensional Series. Read additional information on needle bearing manufacturer.
Its main features are low cross-section height and high load carrying capacity. Mainly used for bearing arrangements that are compact, inexpensive, and the bore of the bearing housing cannot be used as the raceway for the needle roller cage assembly. The bearing and bearing housing must be installed in an interference fit. If the axial positioning function such as the box shoulder and the stop ring can be omitted, the inner hole of the bearing housing can be made extremely simple and economical. The drawn cup needle roller bearings mounted on the shaft end are open on both sides and closed on one side. The base end face of the closed stamped outer ring can withstand small axial guiding forces.
In order to meet the needs of the design engineers, there are three different materials for the cages—- polyamide, steel and brass. For polyamide cages, it features high elasticity, light weight and quiet running from good damping. Bearings with this cage carry the designation suffix ETN, e.g. NU 205ETN. A pressed steel cage is available for many bearings, mainly as an alternative to the polyamide cage, and such bearings are identified by the designation suffix E, e.g. 310E. As for the brass cage, the advantage includes very high strength, suitable for very high speed, accelerations, high temperature and high endurance limit. The bearing with this cage is identified by the designation suffix EM, e.g. NU 207EM.
Jnsn wholesale bearing suppliers parts at great pricing. Fast free, worldwide shipping. Great warranties. Volume discounts. Technical Drawings. Lowest Pricing. Standard precision bearings generally use stamped steel cages. Extra precision bearings, on the other hand, use cages made from stainless steel, bronze, or phenolic— Cages made from these materials offer higher speeds and better loading capabilities.Precision ball bearings are used for high precision applications in a variety of markets, including aerospace, health, machine tool, robotics and general industry.Precision types of bearing are used in critical aeronautical bearings, guidance system balls for space and military applications, valves, automotive bearings, cosmetics, and other applications where higher precision is required. Find extra info at https://www.jnsnbearing.com/.
F6000 series bearings are very similar to normal grooved ball bearings, and the only difference is that this type ball bearings have a flange on the outer ring, which can be very useful for mounting the bearings in through holes or axial location. Flanged deep groove ball bearings F6000 series are available in open, shielded and sealed options. The shields and sealed options provide protection to prevent debris and dust getting into the bearing, while at the same time retaining the grease to ensure good lubrication and a long service life. Metric sized deep groove radial flanged ball bearings can bear heavy radial loads and moderate thrust loads in both directions. These bearings are made to the same sizes as standard bearings 6000 series. They also have a flange, which allows flush fitting into housings up to the flange shoulder. This type of bearing is often used on steel tracks to act as both a guide and a support. Deep groove ball bearings are widely used bearings. They use uninterrupted raceways, making them an excellent choice for radial loads. This design achieves precise tolerances even at high speeds.
JNSN Bearing supplier, manufacturer is specialized in producing different types of bearings, sunch as deep groove ball bearings, self-aligning ball bearings, spherical roller bearings, single row tapered roller bearings, inch tapered bearings, automotive bearings, bearing joints, etc. The annual production capability is more than 960 million units. We have solid teamwork and systematic management to offer one-stop service. We’ll monitor every steps during production, then deliver order timely, and the client just need to wait to receive the items. We’re always here ready to listen to client’s needs and provide economical solutions, suggestions or other helps for the client.
We have plenty available bearings for practically any running precision requirement and application speed: our bearings come in different Abec tolerance grades 1-9, internal clearances vary from C2 to C4, and several different cage designs including J-type, W-type, RJ-type, TW-type, and more. The deep groove bearing 6000 series can also be supplied with a full complement of balls as a filler notch design, which is with filling slots have a filling slot on the inner race as well as on the outer race, so that more and larger balls can be accommodated than with standard deep groove ball bearings. Its structure is simple, it consists of inner and outer rings with deep symmetrical ball race, separator and complement of balls, and it can be easy to operate. The big difference between the full complement style and standard deep groove ball bearing lies in the retainer, the former is without retainer in order to add more balls.
This 6400 series deep groove ball bearing is rated heavy, making it applicable for usage with heavy radial loads and moderate axial loads. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. It has an open design for lubricating the bearing in place. This deep groove ball bearing series is for usage in various applications such as transmissions, motors, pumps, bicycles, machine tools, generators, textile machinery, agriculture machinery and inline skates, among others.